DALI
Energy-efficient lighting control
Our DALI products
Our DALI products work with so-called dynamic lighting control, where lighting during presence goes up to a high light level and after a preset delay, without presence, dims down to a lower light level. After further time, the lighting is turned off completely.
You can connect various detectors to the same DALI bus as the units are able to work together to control the lighting. There are also variations where the lighting is never turned off, but only goes between a high and low light level.
Application areas
PD/PDC35 DL are passive infrared detectors that are intended for presence detection and control of lighting fixtures via a DALI bus. They have a pyroelectric sensor that reacts to changes in heat radiation. PD35 DL has interchangeable lenses for different types of applications. You can also adjust the angle of the detection area by adjusting the height of the card in the housing. The detectors are well-suited for controlling lighting on the same DALI bus in different DALI groups. PD/PDC35 DL has a programming button for programming of DALI groups, light levels, and scenes. You can easily change the light levels via various potentiometers on the detector.
With the "mode bracket," you can choose to control the lighting directly via "direct level" on the DALI bus or "Extronic" which controls the lighting via scene 10 (presence), 14 (low level), 15 (off / constant background light). You can use PD/PDC35 DL or a DALI computer to program the fixtures to those scenes and set the light levels you want. With the help of two potentiometers, you can set the delay time between high/low level and low level/off. You can also start, for example, a fan during presence, via an built-in relay.
Properties PD35 DL och PDC35 DL
In addition to the features of PD33 DL and PDC33 DL:
- Relay output for control of ventilation, for example
- Can program scenes 10,14 and 15 and groups directly on the card with push button
- Adjustable light levels directly on the card
- Adjustable timer for low-level lighting before shut-off from 1 min to 2 hours.
Acoustic detector AD36 DL
The AD-36 DL is a presence detector for energy-saving control of DALI fixtures. The detector listens to sounds within two different frequency ranges that are analyzed for detection of presence. The lighting is turned on by the inaudible "infrasound" with low frequencies 1-3 Hz (LF) that occur, for example, when a door is opened. The lighting is then kept on by higher sound frequencies 4-25 kHz (HF) from footsteps, speech, and other sounds that can confirm the presence. The main function is the automatic turn-on, dimming, and turn-off of the lighting during presence or an empty room.
The detector is pre-set for DALI-BROADCAST and DIRECT LEVEL, which provides quick and easy installation. With this setting, the detector controls all fixtures on the DALI loop to pre-programmed light levels. These functions can be changed to create lighting groups and other light levels.
Locations where AD-36 DL is suitable::
- Stairwells
- Changing rooms
- Shower rooms
- Angled corridors
- Warehouse spaces
- Garages, etc.
Acoustic detector AD36M DL
The acoustic detector AD-36 DL-M has a maximum range of 20-25 m radius depending on the room and interior design. It listens to infrasound (LF) and audible sound (HF) and is powered by a DALI driver via the DALI bus.
Level switches
NP2T DL and NP3T DL are so-called "Level Switches" which also power the DALI bus. NP-3T DL has all the functions that NP-2T DL has, with the big difference that it also has constant light control via the light sensor. The level selectors power the DALI bus with 200mA and control the lighting via Broadcast commands. You can easily set the desired light levels and fade times in the devices with potentiometers. The products are very suitable for installations where you do not want to program the lighting via computer, but still want to set specific light levels and fade times.
We have many application examples with NP2T DL. For example, you can get a constant basic light at certain times via a 22k ohm resistor between terminal 6-7 if you connect the resistor in series with a time channel.
NP-3T DL is preferably used when there are large windows with a lot of light incidence. The lighting level is then adjusted automatically to compensate for the lower level of incoming light, so that there is always a constant level of light in the room.
Example Uses:
- Classrooms
- Offices
- Corridors
- Stairwells
- Garages
Inputs and Outputs:
- Output for DALI fixtures
- Input for presence detector
- Input for light sensor
- Input for push button
- 12 VDC supply to IR detectors
- Relay output for possible driving of contactor.
Level switch NP2T DL
Features: NP2T DL:
- Controls DALI fixtures with broadcast commands
- Dynamic lighting control
- No programming required.
- Built-in power supply to DALI bus
- Power supply voltage 230 VAC.
- Burn-in of fluorescent tubes 100% 100 hours.
- Adjustable extra detector delay time.
Dynamic lighting control in three levels:
- Presence – Normal light
- Timer – Basic light
- Rest – Off
Level switch NP3T DL
Features: NP3T DL:
- Daylight regulation that provides a comfortable light.
- Controls DALI fixtures with broadcast commands.
- No programming required.
- Built-in power supply to DALI bus
- Dynamic lighting control (see diagram on the back).
- Power supply voltage 230 VAC.
- Burn-in of fluorescent tubes 100% 100 hours.
- Adjustable extra detector delay time.
Dynamic lighting control with daylight regulation:
- Presence – Lighting intensity continuously adjusted to daylight
- Timer – Low light level, max 120 minutes
- Rest – Off
Light sensor LS11 är lämplig ljussensor till NP3T DL
Power supply PS1251 DL
DALI-drivare kopplas till 230 VAC och strömförsörjer en DALI-slinga med 250 mA.
Den har dubbla plintar för anslutning till DALI-slingan.
Lysdioder indikerar spänningssatt modul och spänning på DALI-slingan.
Power supply PS1250 DL
The PS-1250DL is a DALI driver which is connected to 230 VAC and supplies a DALI loop with 250 mA. It has double terminals for connection to the DALI loop. LEDs indicate voltage set module and voltage on the DALI loop. For mounting on DIN rail.
Brochure
This brochure provides information about our different products for DALI with various application examples. (Swedish)
